16ga.com Forum Index
Author Message
<  16ga. Ammunition & Reloading  ~  1 oz Green Dot loads
mike campbell
PostPosted: Sun Oct 14, 2018 9:17 am  Reply with quote
Member
Member


Joined: 16 Nov 2006
Posts: 1338

Rolling Eyes


Last edited by mike campbell on Fri Jul 26, 2019 9:47 am; edited 1 time in total
Back to top
View user's profile Send private message
Dogchaser37
PostPosted: Sun Oct 14, 2018 9:44 am  Reply with quote
Member
Member


Joined: 08 Aug 2011
Posts: 1946
Location: Central CT

Mike,

I converted to Universal and never bothered with 20/28....not for any particular reason other than I had already developed the loads I wanted with Universal.

The only loads that I know about using Remington hulls and 20/28 are on Old Hunter's spreadsheets. They were done by a fellow Sorrentino, 15.5 grains of 20/28, using Win, Ched and Rem primers, DR16 and 7/8 oz of lead. pressures are 5700 to 6200 and the velocities are 1100 to 1125.


I have about one year worth of experience with the 'new' Unique and 7/8 oz. loads. I like it and it didn't soot up my 1100 like the 'old' Unique.

Kind of a nice load really.

Remington Hull
Winchester 209
20.0 grains Unique
CB0078-16 wad
7/8 oz. of lead shot.

This is a takeoff of a Unique 1 oz. load. I have no idea of the velocity but it kills pen raised pheasants just fine. I also used it for Sporting Clays. It does cycle the 1100 without a glitch.

_________________
Mark
Back to top
View user's profile Send private message
Byron Whitlock
PostPosted: Sun Oct 14, 2018 3:10 pm  Reply with quote



Joined: 27 Jan 2016
Posts: 488
Location: Oswego, Kansas

I loaded Unique for many years beginning with 20ga and handgun loads for 38, 45, 10mm and 44spec. before I used it in my 16ga. It always worked great in my handgun loads and metered well in my powder measure. I found it to be clean burning in the handgun but the 16ga loads did get a little dirty.
I have since switched to Ramshot Silhouette powder for my handgun loads and have been experimenting with Vectan powders in my 16 and 20ga loads with good success.

_________________
Sweet sixteen forever
LC Smith Field Grade
LC Smith Ideal Grade
CZ Ringneck
Win. Model 12
Rem M11
Stevens 235
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger
castnblast
PostPosted: Sun Oct 14, 2018 5:35 pm  Reply with quote



Joined: 28 May 2008
Posts: 84

I worked up a new pheasant load using Fed hull, 209A, 21.7 gr. Unique, CB16 wad and 1 1/8 oz nickel 5.5's. Should be about 1220 FPS. Can't wait to try in Nebraska end of the month.
Back to top
View user's profile Send private message
kgb
PostPosted: Sun Oct 14, 2018 7:02 pm  Reply with quote
Member
Member


Joined: 31 Aug 2005
Posts: 1256
Location: Nebraska

Larry Brown submitted at least one, 2 3/4" Herters hull, Cheddite 209, 17.3gr 20/28 and DR16 with 7/8oz of lead shot. Avg 7420psi, 1182fps.

_________________
Bore, n. Shotgun enthusiast's synonym for "gauge" ; everybody else's synonym for "shotgun enthusiast." - Ed Zern
Back to top
View user's profile Send private message
DanLee
PostPosted: Mon Oct 15, 2018 6:46 am  Reply with quote
Member
Member


Joined: 15 Mar 2007
Posts: 601
Location: Virginia

Unique and 20/28 are very close in burning rate and can be substituted for each other by weight. However, 20/28 is more dense, so a given powder bushing will drop a greater weight of 20/28 than Unique. I have used both at the same weight in the 16. The only difference is the space between the shot and the hull mouth if the same wad and shot charges are used. 20/28 was developed to be used in the new Winchester 28-gauge HS hull when stack height proved to be a problem with traditional charges of Unique.
Back to top
View user's profile Send private message
Ohio Wirehair
PostPosted: Tue Oct 16, 2018 8:52 pm  Reply with quote



Joined: 24 Jul 2016
Posts: 546
Location: Ohio

Lyman 5th - Federal 209A 19.5 Grns of Green Dot, Rem SP16 wad,1 oz. of shot. 1257 FPS, 10,700 PSI. I don't like Remington wads in Federal hulls because of powder migration. Someone with a lot of knowledge that I trust suggested dropping back 1 or 2 grains of powder and using a nitro card over the shot. I went to 18 grns and everything is good IMHO.
Back to top
View user's profile Send private message
WyoChukar
PostPosted: Tue Oct 23, 2018 9:19 pm  Reply with quote



Joined: 16 Jul 2015
Posts: 2124
Location: Hudson,Wy

Don't you mean put a nitro card over the powder to stop migration?

_________________
Only catch snowflakes on your tongue AFTER the birds fly south for the winter...
Back to top
View user's profile Send private message
Carlos
PostPosted: Wed Oct 24, 2018 6:27 am  Reply with quote



Joined: 21 May 2010
Posts: 602
Location: Victoria BC Canada

WyoChukar wrote:
Don't you mean put a nitro card over the powder to stop migration?


Isn't an Over Shot card enough to keep the powder from leaking?
Back to top
View user's profile Send private message Send e-mail
JNW
PostPosted: Wed Nov 07, 2018 10:53 pm  Reply with quote



Joined: 15 Jun 2010
Posts: 1358
Location: Twin Cities, MN

I’ve loaded some 7/8 and 1 oz 20/28 loads in Cheddites and Federals. Have to look in my reloading log to see how much powder, what they chronographed at and how it burned. I did settle on a 1 oz GD load, but I have a fair bit of GD to burn up. I can dig it out if anyone’s really interested.
Jeff
Back to top
View user's profile Send private message
Display posts from previous:   
All times are GMT - 7 Hours

View next topic
View previous topic
Page 2 of 2
Goto page Previous  1, 2
16ga.com Forum Index  ~  16ga. Ammunition & Reloading

Post new topic   Reply to topic


 
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum




Powered by phpBB and NoseBleed v1.09