16ga.com Forum Index
Author Message
<  16ga. General Discussion  ~  need a barrel inspected
3drahthaars
PostPosted: Mon Dec 20, 2021 7:24 am  Reply with quote



Joined: 21 May 2015
Posts: 127

So, I have a low grade Sauer SxS with some pitting in the barrels. I've shot it for a few years with off the shelf ammo, and I've all of my fingers.

It's a nice little beater right at 6#, too.

But, it has some pitting, and depending upon the light it can look worse some days.

I'm pretty much set up for reloading low pressure loads6500 psig max... about 66% of SAMMI max.

But, I'd like a good gun smith to give me an honest evaluation of the barrels before I retire it for good.

Please any suggestions on some one who can inspect and take thickness measurements?

Thanks,
Back to top
View user's profile Send private message
PatrickB
PostPosted: Mon Dec 20, 2021 7:41 am  Reply with quote
Member
Member


Joined: 16 Dec 2007
Posts: 592
Location: Minnesota

Where are you located...might help with suggestions from members
Back to top
View user's profile Send private message
3drahthaars
PostPosted: Mon Dec 20, 2021 7:48 am  Reply with quote



Joined: 21 May 2015
Posts: 127

Raleigh, NC


Thanks
Back to top
View user's profile Send private message
GF1
PostPosted: Thu Dec 30, 2021 4:24 am  Reply with quote
Member
Member


Joined: 08 Jun 2009
Posts: 107
Location: Idaho

I’d consider Jim Kelly, Darlington Gun Works, Darlington SC.
Back to top
View user's profile Send private message
Dave in Maine
PostPosted: Thu Dec 30, 2021 7:58 am  Reply with quote



Joined: 12 Sep 2010
Posts: 1972
Location: Maine

I'd say the most objective result you could possibly hope for from any responsible gunsmith would be measuring he barrels for minimum wall thickness. No one is going to say "this gun is safe for you to shoot" because of liability concerns. Going through his mind would be things like "He says he shoots only 6500psi shells through this, but does he really? And will whomever he loans it to also shoot light shells?" and "Will this guy have an obstruction, blow up a barrel and then blame me for saying it was safe?" and "Just how many shells is he really running through this?"

Face to face if you ask "is it safe to shoot?" you might get a queasy or other unpleasant facial expression but surely no words saying "yes".

What it boils down to is: if you feel it's possibly unsafe to shoot or there's a question in your mind about its safety, then it's unsafe to shoot.

Besides, if you feel it might be unsafe to shoot you'll likely not shoot it well, if only because in your mind you won't be confident in it.

_________________
“A man’s rights rest in three boxes: the ballot box, the jury box, and the cartridge box.”
Frederick Douglass, November 15, 1867, speech in Williamsport, Pa.
Back to top
View user's profile Send private message
nj gsp
PostPosted: Thu Dec 30, 2021 5:22 pm  Reply with quote



Joined: 09 Aug 2007
Posts: 437
Location: WI

Depending on the barrel wall thickness, you can have the barrels back bored. It will clean up the pitting and you'll have a usable gun.
Back to top
View user's profile Send private message Visit poster's website
16'er
PostPosted: Fri Dec 31, 2021 4:03 am  Reply with quote
Member
Member


Joined: 08 Oct 2006
Posts: 1393
Location: Tappahannock, Virginia

Ive got a Sauer on the way to Pfrommer Gunworks, rocky mount va to be evaluated by Gunther. I’ve seen some of his work, including a complete restoration of a Fox A grade 16. Amazing work.
Back to top
View user's profile Send private message
Swampy16
PostPosted: Fri Dec 31, 2021 4:52 pm  Reply with quote



Joined: 17 Oct 2019
Posts: 453
Location: New Jersey

If it were my gun I only trust Dean Harris at Skeets Gun Shop in Ok. He’s a barrel magician and very pleasant to deal with. He can measure it, and hone/polish the bores (if possible, if there’s enough meat). He’s worked on several barrels for me including a Sauer 16 (dent removal). I don’t like to leave pits in a barrel, I prefer to have them polished out. I feel they can cause unnecessary stresses.
Back to top
View user's profile Send private message
PeeDeeSetters
PostPosted: Fri Dec 31, 2021 6:25 pm  Reply with quote



Joined: 19 Nov 2021
Posts: 1
Location: NC

I 2nd Jim Kelly, Darlington Gun Works, Darlington SC.
Back to top
View user's profile Send private message
3drahthaars
PostPosted: Mon Jan 03, 2022 8:33 am  Reply with quote



Joined: 21 May 2015
Posts: 127

To everyone, thanks for the responses... I don't have much money in the gun but I'd like to keep it on the bench for a bad weather beater.

Happy New Year and thanks,

3d
Back to top
View user's profile Send private message
Display posts from previous:   
All times are GMT - 7 Hours

View next topic
View previous topic
Page 1 of 1
16ga.com Forum Index  ~  16ga. General Discussion

Post new topic   Reply to topic


 
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum




Powered by phpBB and NoseBleed v1.09