Author |
Message |
< 16ga. Ammunition & Reloading ~ WSF 1 oz experiments |
|
Posted:
Thu May 04, 2023 11:20 am
|
|
|
Joined: 13 Oct 2015
Posts: 151
Location: SE Ks
|
|
I got the WSF powder yesterday so this morning I did some experimenting. The little data I'd found on the web and the old Yahoo site sheets led me to believe that 22 gr with 1 oz shot would work well for the straight wall cases. I loaded one old Herters Cheddite hull each with SG-16, Z-16 and the pink CB0078-16 with the powder cup flared to help fend off powder migration. The SG-16 yielded a bit more dished crimp than I'd like, the Z-16 WAY more dish, but the CB0078 was pretty good. Shells were loaded with my Mec Sizemaster.
I ran each of them over my Competition Electronics ProChrono. It was heavily overcast getting ready to rain and I didn't use the skyscreens on the chronograph. Roughly 3 feet muzzle to chrono
All used CCI 209 Primers.
The SG-16 load gave 1228 fps
Z-16 1263
CB0078-16 1277
Then I dropped bushing size to 20.6 gr WSF and loaded 3 with the CB0078-16.
Ave 1215, with ES of 10
I'm going to need to load a few with the flared cup CB0078 and do some shaking of them to see if powder migration will be a problem.
This stack height issue with published loads is a real issue with the 16 ga. It's still my favorite though. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu May 04, 2023 12:40 pm
|
|
|
Joined: 27 Aug 2020
Posts: 93
Location: SE TX Marsh and Young County Tx
|
|
Thanks! Going to try loading some WSF I have with 1 oz loads. Looking at your load with the cb wad is promising. that is about the velocity I want. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu May 04, 2023 4:52 pm
|
|
|
Joined: 08 Mar 2022
Posts: 91
|
|
hahahah Ironically i too just bought 1lb of WSF. Went into all my spreadsheets & Lyman and came up with 24 different loads that i might try. These may pertain to you.
Ole_270 - Fed hull, 1oz, w209, waa16 (migration ? ) 22gWSF, 1230/7500 Ly5
Fio hull, 1 oz, f616, Sg16, 21.3 gr WSF, 1230/8900 RFS 4
WCF hull, 1oz, w209, waa16 OR cb100, 21gr WSF, 1220/9000, W15
DUKFVR- Ched/Win Ched hull, 1oz, w209, SP16 (migration ? ) 22gr WSF 1265/8500 LY 5 source
Rem hull, 1oz, w209, SP16 ( migration ?) 21.5gr WSF, 1282/10,500 Ly5
WCF, 1oz, w209, SP16, 20.5 WSF, 1262/10,000, Ly5 |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu May 04, 2023 7:49 pm
|
|
|
Joined: 27 Aug 2020
Posts: 93
Location: SE TX Marsh and Young County Tx
|
|
Thanks probie.
Been looking at Lyman & hodgdon manuals. Thanks for the oads. Will definitely try cheddite load. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Fri May 05, 2023 5:31 am
|
|
|
Joined: 30 Sep 2015
Posts: 640
Location: NEW SALISBURY INDIANA
|
|
also bought some wsf to replace universal, using rem game load hulls, claybuster 1 oz wads and 18.9 grs of wsf gives me about 1150 fps, using it for trap, its dirtier then universal but gets the job done |
_________________ 16ga 3-Win 37
16ga Ithaca 37 1946
16ga Western Auto Revelation
16ga Browning A-5 1929
16ga Marlin 90 1939
16ga browning citori lightning grade 3 2003
16ga Francisque Darne 1920 |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Fri May 05, 2023 5:51 am
|
|
|
Joined: 08 Mar 2022
Posts: 91
|
|
It should go w/o saying but i'll say it anyway. With the current powder shortages i'm open to sometimes experimenting with different powders. I never have used WSF before, and like yous have obtained some because it was available and i have access to alot of data. I don't like the fact that the data in some cases, from supposedly reputable publications, are still using what some say is the wrong wad for the hull with migration or stack issues. I know of guys who use an over powder card to deal with migration issues and some still use rice, cheerios, beans popcorn pips etc to get better stack heights. Many say one shouldn't have to do that; find a load that works. Easier said than done sometimes, especially for a newbie and dealing with component issues.
Kennedy.. where did you find that data ? Are you using that in a Rem black shortie ?
Did you chrono it & its a concave load, correct? |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Fri May 05, 2023 10:38 am
|
|
|
Joined: 30 Sep 2015
Posts: 640
Location: NEW SALISBURY INDIANA
|
|
I am using it in a regular black game load hull, I used a chrony to first measure my universal load 17,4 grs then starting with the same grs of wsf worked up until I got the same fps. my crimps look the same, real close to factory crimp |
_________________ 16ga 3-Win 37
16ga Ithaca 37 1946
16ga Western Auto Revelation
16ga Browning A-5 1929
16ga Marlin 90 1939
16ga browning citori lightning grade 3 2003
16ga Francisque Darne 1920 |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Fri May 05, 2023 12:18 pm
|
|
|
Joined: 13 Oct 2015
Posts: 151
Location: SE Ks
|
|
A bit more experimenting. I had some new, primed Fiocchi cases that I tried with the CB0078 pink wad, 1 oz Eagle #8, and 21 gr WSF. I wasn't real happy with the amount of dish in the crimp so I called my wife who was in town and asked her to bring home some dry beans for filler. I asked for something the size of black eyed peas but she got lentils. 6 of them fit nicely around the center post in the pink wad and crimped a lot better. Still a slight dish but not bad. Doubt they would weigh enough to change pressure considerably.
Patterns were pretty good, especially the one with 1 oz Lawrence Magnum 7 1/2. Used my Dickinson Estate SxS with the IC choke at 25 yards. 3 shots over the ProChrono went 1206, 1203 and 1233. Thinking that as fine grained and dense as WSF is an extra bump on the loader might vary the charge rate. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Sat May 06, 2023 3:12 pm
|
|
|
Joined: 22 Dec 2004
Posts: 173
Location: S. E. Arizona
|
|
I have been using WSF in 1 oz. 16b loads for many years in my Fox 16. Load is:
20 grns WSF
Win209 primer
WAA16 hull
WAA16 wad
I've killed a lot of game and countless clay targets. It just works. |
_________________ Country to hunt, my setters, and a Fox 16 gauge...
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Sat May 06, 2023 4:57 pm
|
|
|
Joined: 08 Mar 2022
Posts: 91
|
|
Churkarman, YES, i've got that one too... |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Sun May 07, 2023 7:50 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 30 Nov 2011
Posts: 1698
Location: Minnesota
|
|
Chukarman,do you have the velocity/pressure for that one? |
_________________ Great dog, Great friends,Great guns |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Sun May 07, 2023 7:37 pm
|
|
|
Joined: 08 Jan 2017
Posts: 12
|
|
I have recently tried WSF in cheddite (once fired herters) hulls with SG-16 wads and 1 1/16th ounce of shot. 21.5 grains of powder with this combination gives me consistent velocities of 1260-1270 fps range and excellent patterns and near perfect crimps. The field commander (Z-16) wad gave slightly dished crimps but a .125” 28ga. card wad in the bottom of shot cup fixed the crimps. Velocities were slightly less (1240-1250 range) with this wad and patterns were good. Cheddite 1632 wads with WSF and 1 1/8th ounce of shot did not pattern particularly well regardless of powder charge weight used.
*used win primers for all loads above |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed May 10, 2023 10:47 am
|
|
|
Joined: 22 Dec 2004
Posts: 173
Location: S. E. Arizona
|
|
Savage16 wrote: |
Chukarman,do you have the velocity/pressure for that one?
|
I have two sources/attributions:
Lyman's 4th edition: 1223 fps/ 9700LUP
Winchester Western:1165 fps/ 8400 PSI
I've been using this load in my Fox 16 for many years. |
_________________ Country to hunt, my setters, and a Fox 16 gauge...
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed May 10, 2023 10:48 am
|
|
|
Joined: 22 Dec 2004
Posts: 173
Location: S. E. Arizona
|
|
Double post - I keep getting an error message, but the post shows up on the thread. ? |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed May 10, 2023 11:44 am
|
|
|
Joined: 27 Aug 2020
Posts: 93
Location: SE TX Marsh and Young County Tx
|
|
Chukarman wrote: |
Double post - I keep getting an error message, but the post shows up on the thread. ?
|
It does the same thing when I post ,but goes through. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|